initial commit

proprietary/vendor/firmware/wlan/qcom_cfg.ini

@@ -0,0 +1,457 @@
+# This file allows user to override the factory
+# defaults for the WLAN Driver
+
+# Phy Mode (auto, b, g, n, etc)
+# Valid values are 0-12, with 0(Min) = Auto, 12(Max) = 11ax
+# 1 = 11abg, 2 = 11b, 3 = 11g, 4 = 11n, 5 = 11g only, 6 = 11n only
+# 7 = 11b only 8 = 11ac only, 9 = 11ac, 12 = 11ax.
+gDot11Mode=0
+twt_responder=0
+#Enable Modulated DTIM
+gEnableModulatedDTIM=3
+
+#Max modulated DTIM
+gMaxLIModulatedDTIM=5
+
+# UAPSD service interval for VO,VI, BE, BK traffic
+InfraUapsdVoSrvIntv=0
+InfraUapsdViSrvIntv=0
+InfraUapsdBeSrvIntv=0
+InfraUapsdBkSrvIntv=0
+
+# Flag to allow STA send AddTspec even when ACM is Off
+gAddTSWhenACMIsOff=1
+
+#Enable OBSS protection
+gEnableApOBSSProt=1
+
+# Maximum Tx power
+# gTxPowerCap=30
+
+# Fragmentation Threshold
+# gFragmentationThreshold=2346
+
+# RTS threshold
+RTSThreshold=1048576
+
+# WMM Enable/Disable
+WmmIsEnabled=0
+
+# 802.11d support
+g11dSupportEnabled=0
+
+# DFS Master Capability
+gEnableDFSMasterCap=1
+
+ImplicitQosIsEnabled=0
+
+gNeighborScanTimerPeriod=45
+gNeighborLookupThreshold=75
+
+# Legacy (non-ESE, non-802.11r) Fast Roaming Support
+# To enable, set FastRoamEnabled=1
+# To disable, set FastRoamEnabled=0
+FastRoamEnabled=1
+
+#Channel Bonding
+gChannelBondingMode5GHz=1
+
+is_bssid_hint_priority =1
+
+#Say gGoKeepAlivePeriod(5 seconds) and gGoLinkMonitorPeriod(10 seconds).
+#For every 10 seconds DUT send Qos Null frame(i.e., Keep Alive frame if link
+#is idle for last 10 seconds.) For both active and power save clients.
+
+#Power save clients: DUT set TIM bit from 10th second onwards and till client
+#honors TIM bit. If doesn't honor for 5 seconds then DUT remove client.
+
+#Active clients: DUT send Qos Null frame for 10th seconds onwards if it is not
+#success still we try on 11th second if not tries on 12th and so on till 15th
+#second. Hence before disconnection DUT will send 5 NULL frames. Hence in any
+#case DUT will detect client got removed in (10+5) seconds.
+#i.e., (gGoKeepAlivePeriod + gGoLinkMonitorPeriod)..
+
+#gGoLinkMonitorPeriod/ gApLinkMonitorPeriod is period where link is idle and
+#it is period where we send NULL frame.
+#gApLinkMonitorPeriod = 10
+#gGoLinkMonitorPeriod = 10
+
+#gApKeepAlivePeriod is time to spend to check whether frame
+#are succeed to send or not. Hence total effective detection time is
+#(gApLinkMonitorPeriod + gApKeepAlivePeriod)
+
+#STA Keepalive Period 	
+gStaKeepAlivePeriod=15
+
+# Enable DFS channel roam
+# 0: DISABLE, 1: ENABLED_NORMAL, 2: ENABLED_ACTIVE
+gAllowDFSChannelRoam=1
+
+gVhtChannelWidth=2
+
+# Set txchainmask and rxchainmask
+# These parameters are used only if gEnable2x2 is 0
+# Valid values are 1,2
+# Set gSetTxChainmask1x1=1 or gSetRxChainmask1x1=1 to select chain0.
+# Set gSetTxChainmask1x1=2 or gSetRxChainmask1x1=2 to select chain1.
+gSetTxChainmask1x1=1
+gSetRxChainmask1x1=1
+
+# MCC to SCC Switch mode:
+# 0-Disable
+# 1-Enable
+# 2-Force SCC if same band, with SAP restart
+# 3-Force SCC if same band, without SAP restart by sending (E)CSA
+# 4-Force SCC if same band (or) use SAP mandatory channel for DBS,
+#   without SAP restart by sending (E)CSA
+gWlanMccToSccSwitchMode = 4
+
+# 1=enable tx STBC; 0=disable
+gEnableTXSTBC=1
+
+#Enable/Disable Tx beamformee in SAP mode
+gEnableTxBFeeSAP=1
+
+# Enable Tx beamforming in VHT20MHz
+# Valid values are 0,1. If commented out, the default value is 0.
+# 0=disable, 1=enable
+gEnableTxBFin20MHz=1
+
+#Enable/Disable SU Tx beamformer support
+gEnableTxSUBeamformer=1
+
+# 802.11K support
+gRrmEnable=1
+
+# Firmware log mode
+# Valid values are 0,1,2
+# 0=Disable, 1=WMI, 2=DIAG
+gEnablefwlog=1
+
+# Maximum Receive AMPDU size (VHT only. Valid values:
+# 0->8k 1->16k 2->32k 3->64k 4->128k)
+gVhtAmpduLenExponent=7
+
+# Maximum MPDU length (VHT only. Valid values:
+# 0->3895 octets, 1->7991 octets, 2->11454 octets)
+gVhtMpduLen=2
+
+#Enable or Disable p2p device address administered
+isP2pDeviceAddrAdministrated=1
+
+#Enable VHT on 2.4Ghz
+gEnableVhtFor24GHzBand=1
+
+#Maximum number of offload peers supported
+# gMaxOffloadPeers=2
+
+# controlling the following offload patterns
+# through ini parameter. Default value is 1
+# to disable set it to zero. ssdp = 0
+# Setup multicast pattern for mDNS 224.0.0.251,
+# SSDP 239.255.255.250 and LLMNR 224.0.0.252
+ssdp=0
+
+# RA filtering rate limit param, the current value would not
+# help if the lifetime in RA is less than 3*60=3min. Then
+# we need to change it, though it is uncommon.
+# gRAFilterEnable=0
+gRArateLimitInterval=600
+
+# Maximum number of concurrent connections
+gMaxConcurrentActiveSessions=3
+
+# Disable/Enable GreenAP
+# 0 to disable, 1 to enable, default: 1
+gEnableGreenAp=0
+
+#Enable/Disable LPASS support
+# 0 to disable, 1 to enable
+gEnableLpassSupport=1
+
+# Whether userspace country code setting shld have priority
+gCountryCodePriority=1
+
+# Enable or Disable Multi-user MIMO
+# 1=Enable (default), 0=Disable
+gEnableMuBformee=1
+
+# Enable support for TDLS
+#  0 - disable
+#  1 - enable
+gEnableTDLSSupport=1
+
+# Enable support for Implicit Trigger of TDLS. That is, wlan driver shall
+# initiate TDLS Discovery towards a peer whenever setup criteria (throughput
+# and RSSI) is met and then will initiate teardown when teardown criteria
+# (idle packet count and RSSI) is met.
+#  0 - disable
+#  1 - enable
+gEnableTDLSImplicitTrigger=1
+
+# Changed to 0 for Samsung to enable explicit TDLS withough supplicant change
+# Enable TDLS External Control. That is, user space application has to
+# first configure a peer MAC in wlan driver towards which TDLS is desired.
+# Device will establish TDLS only towards those configured peers whenever
+# TDLS criteria (throughput and RSSI threshold) is met and teardown TDLS
+# when teardown criteria (idle packet count and RSSI) is met. However,
+# device will accept TDLS connection if it is initiated from any other peer,
+# even if that peer is not configured.
+#  0 - disable
+#  1 - enable
+# For TDLS External Control, Implicit Trigger must also be enabled.
+gTDLSExternalControl=0
+
+# Changed to 0 for Samsung to disable TDLS offchannel
+# Enable support for TDLS off-channel operation
+#  0 - disable
+#  1 - enable
+# TDLS off-channel operation will be invoked when there is only one
+# TDLS connection.
+gEnableTDLSOffChannel=0
+
+gSoftApMaxPeers=8
+gTDLSMaxPeerCount=1
+
+# Enable Mutiple TDLS links
+gEnableTDLSBufferSta=0 
+gTDLSUapsdMask=0
+gTDLSRSSITeardownThreshold=-95
+
+# TDLS Packet Threshold
+gTDLSTxPacketThreshold=200
+
+# VHT Tx/Rx MCS values
+# Valid values are 0,1,2. If commented out, the default value is 0.
+# 0=MCS0-7, 1=MCS0-8, 2=MCS0-9
+gVhtRxMCS=2
+gVhtTxMCS=2
+
+# VHT Tx/Rx MCS values for 2x2
+# Valid values are 0,1,2. If commented out, the default value is 0.
+# 0=MCS0-7, 1=MCS0-8, 2=MCS0-9
+gEnable2x2=1
+gVhtRxMCS2x2=2
+gVhtTxMCS2x2=2
+
+#IPA config is a bit mask and following are the configurations.
+#bit0 IPA Enable
+#bit1 IPA PRE Filter enable
+#bit2 IPv6 enable
+#bit3 IPA Resource Manager (RM) enable
+#bit4 IPA Clock scaling enable
+#bit5 IPA uC ENABLE
+#bit6 IPA uC STA ENABLE
+#bit8 IPA Real Time Debugging
+gIPAConfig=0
+gIPADescSize=800
+
+# Increase TCL ringsize
+dp_tx_ring_size=3072
+
+#Disable HW checksum for Legacy modes 
+legacy_mode_csum_disable=1
+
+# Enable TCP Segmentation Offload
+# 1 - enable  0 - disable
+TSOEnable=1
+
+# Enable Generic Receive Offload
+# 1 - enable(default)  0 - disable
+GROEnable=1
+
+# Enable HT MPDU Density
+# 4 for 2 micro sec
+ght_mpdu_density=4
+
+# Enable flow steering to enable multiple CEs for Rx flows.
+# Multiple Rx CEs<==>Multiple Rx IRQs<==>probably different CPUs.
+# Parallel Rx paths.
+# 1 - enable 0 - disable(default)
+gEnableFlowSteering=1
+
+# Enable Rx FISA support
+# 0 - disable(default for non-QCA6490), 1 - enable(default for QCA6490)
+dp_rx_fisa_enable=0
+
+# Maximum number of MSDUs the firmware will pack in one HTT_T2H_MSG_TYPE_RX_IN_ORD_PADDR_IND
+maxMSDUsPerRxInd=8
+
+################ Datapath feature set End ################
+
+################ NAN feature set start ###################
+
+# Enable NAN discovery (NAN 1.0)
+# 1 - enable  0 - disable(default)
+gEnableNanSupport=1
+# Enable NAN Datapath
+genable_nan_datapath=1
+
+################ NAN feature set end #####################
+
+hostscan_adaptive_dwell_mode=1
+
+# Enable/Disable rtt sta mac randomization
+enable_rtt_mac_randomization=1
+
+#Enable/Disable SNR monitoring
+gEnableSNRMonitoring=1
+
+gEnableConcurrentSTA=wlan1
+gEnableSAPManadatoryChanList=1
+
+# HTC Credit count for WMI operation
+# 1 to serialize the WMI commands
+# 0 default works with FW advertised credits, 2 credits usually
+gWmiCreditCount=1
+
+# Added for Samsung HST
+# For enabled 11ac SAP
+gSAP11ACOverride=1
+# Enable enhanced ACS
+acs_with_more_param=1
+# bits 0-3:   rssi weight
+# bits 4-7:   bss count weight
+# bits 8-11:  noise floor weight
+# bits 12-15: channel free weight
+# bits 16-19: tx power range weight
+# bits 20-23: tx power throughput weight
+# bits 24-31: reserved
+AutoChannelSelectWeight=0x00fafafa
+
+# Enable/Disable broadcast TWT
+bcast_twt=1
+
+#Disable twt    
+twt_congestion_timeout=0
+
+# Enable Runtime PM
+# 0 - RTPM disabled, so CxPC aware RTPM will be disabled as well
+# 1 - RTPM enabled, but CxPC aware RTPM disabled (i.e, Static Runtime PM)
+# 2 - RTPM enabled and CxPC aware RTPM enabled as well (i.e, Dynamic Runtime PM)
+gRuntimePM=0	
+gRuntimePMDelay=500
+
+# QMI stats
+enable_qmi_stats=0
+
+# sae connect retry
+sae_connect_retries=0x52
+
+# join retry timer on failure
+join_failure_retry_interval=1000
+
+gActiveMaxChannelTime=80
+active_max_channel_time_6g=60
+passive_max_channel_time_6g=60
+
+# Enable broadcast logging to the userspace entities
+gMulticastHostFwMsgs=1
+# Disable packetlog explicitly
+gEnablePacketLog=0
+
+# Set IPA bandwidth levels in mbps
+gIPALowBandwidthMbps=100
+gIPAMediumBandwidthMbps=400
+gIPAHighBandwidthMbps=800
+
+# Enable wlm_latency_enable feature
+# 0 - disable, 1 - enable(default)
+wlm_latency_enable=1
+wlm_latency_flags_low=0x420000 
+wlm_latency_flags_ultralow=0x420000
+spectral_disable=1
+
+# This ini is used to give higher priority for 5g scc than dbs.
+# It is bitmap per enum policy_mgr_con_mode.
+# For example in GO+STA(5G) mode, when TPUT is onfigured as wlan system
+# preference option, If 5G SCC needs higher priority than dbs, set it as 8.
+g_prefer_5g_scc_to_dbs=8
+
+# To get PCIe debug info
+gEnableSelfRecovery=1
+#Roaming enhancements related ini
+enable_bss_load_roam_trigger=1
+bss_load_threshold=70
+bss_load_sample_time=10000
+bss_load_trigger_2g_rssi_threshold=-60
+bss_load_trigger_5g_rssi_threshold=-70
+enable_idle_roam=1
+idle_roam_band=1
+idle_roam_inactive_time=10
+idle_roam_min_rssi=-60
+idle_roam_rssi_delta=5
+idle_data_packet_count=5
+enable_disconnect_roam_offload=1
+enable_adaptive_11r=1
+gNeighborLookupThreshold=75
+gEmptyScanRefreshPeriod=10000
+roam_scan_inactivity_time=10000
+roam_scan_period_after_inactivity=120000
+roam_inactive_data_count=5
+roam_score_delta=20
+roam_score_delta_bitmap=0xFFFFFFFF
+btm_roam_score_delta=0
+idle_roam_score_delta=1
+candidate_min_rssi_for_beacon_miss=-76
+candidate_min_rssi_for_disconnect=-76
+btm_disassoc_timer_threshold=10000
+nr_offload_params_bitmask=1
+nr_offload_time_offset=1
+btm_offload_config=449
+roam_candidate_validity_timer=0
+minimum_btm_candidate_score=6000
+roam_bad_rssi_thresh_offset_2g=0
+roam_bg_scan_client_bitmap=0
+rssi_weightage=65
+channel_congestion_weightage=35
+ht_caps_weightage=0
+vht_caps_weightage=0
+he_caps_weightage=0
+chan_width_weightage=0
+nss_weightage=0
+chan_band_weightage=0
+beamforming_cap_weightage=0
+pcl_weightage=0
+oce_wan_weightage=0
+vendor_roam_score_algorithm=1
+gNeighborScanChannelMaxTime=40
+gRoamScanHomeAwayTime=100
+RoamRssiDiff=10
+gFullRoamScanPeriod=120
+gRoamScanNProbes=2
+gWESModeEnabled=0
+min_roam_score_delta=1500
+gper_roam_enabled=0
+groam_dense_rssi_thresh_offset=0
+gRoamScanHiRssiDelta=0
+gChannelBondingMode24GHz=1
+sae_single_pmk_feature_enabled=1 
+gDroppedPktDisconnectTh=0
+gEnableNUDTracking=0
+
+#gEnableIpTcpUdpChecksumOffload=0
+gHandleLatencyCriticalClients=1
+
+etsi13_srd_chan_in_master_mode=7
+
+#acquire wake lock during user scan
+wake_lock_in_user_scan=1
+
+enable_tcp_param_update=1
+
+#Removed by request of SS 
+#enable_bcn_rpt_err_vsie=1
+
+#Removed by request of SS 
+#enable_roam_reason_vsie=1
+
+sta_disable_roam=3
+
+#Enable PNO on R-OS
+gPNOScanSupport=1
+
+END
+
+# Note: Configuration parser would not read anything past the END marker
+