initial commit
This commit is contained in:
doomvrr
+457
@@ -0,0 +1,457 @@
|
||||
# This file allows user to override the factory
|
||||
# defaults for the WLAN Driver
|
||||
|
||||
# Phy Mode (auto, b, g, n, etc)
|
||||
# Valid values are 0-12, with 0(Min) = Auto, 12(Max) = 11ax
|
||||
# 1 = 11abg, 2 = 11b, 3 = 11g, 4 = 11n, 5 = 11g only, 6 = 11n only
|
||||
# 7 = 11b only 8 = 11ac only, 9 = 11ac, 12 = 11ax.
|
||||
gDot11Mode=0
|
||||
twt_responder=0
|
||||
#Enable Modulated DTIM
|
||||
gEnableModulatedDTIM=3
|
||||
|
||||
#Max modulated DTIM
|
||||
gMaxLIModulatedDTIM=5
|
||||
|
||||
# UAPSD service interval for VO,VI, BE, BK traffic
|
||||
InfraUapsdVoSrvIntv=0
|
||||
InfraUapsdViSrvIntv=0
|
||||
InfraUapsdBeSrvIntv=0
|
||||
InfraUapsdBkSrvIntv=0
|
||||
|
||||
# Flag to allow STA send AddTspec even when ACM is Off
|
||||
gAddTSWhenACMIsOff=1
|
||||
|
||||
#Enable OBSS protection
|
||||
gEnableApOBSSProt=1
|
||||
|
||||
# Maximum Tx power
|
||||
# gTxPowerCap=30
|
||||
|
||||
# Fragmentation Threshold
|
||||
# gFragmentationThreshold=2346
|
||||
|
||||
# RTS threshold
|
||||
RTSThreshold=1048576
|
||||
|
||||
# WMM Enable/Disable
|
||||
WmmIsEnabled=0
|
||||
|
||||
# 802.11d support
|
||||
g11dSupportEnabled=0
|
||||
|
||||
# DFS Master Capability
|
||||
gEnableDFSMasterCap=1
|
||||
|
||||
ImplicitQosIsEnabled=0
|
||||
|
||||
gNeighborScanTimerPeriod=45
|
||||
gNeighborLookupThreshold=75
|
||||
|
||||
# Legacy (non-ESE, non-802.11r) Fast Roaming Support
|
||||
# To enable, set FastRoamEnabled=1
|
||||
# To disable, set FastRoamEnabled=0
|
||||
FastRoamEnabled=1
|
||||
|
||||
#Channel Bonding
|
||||
gChannelBondingMode5GHz=1
|
||||
|
||||
is_bssid_hint_priority =1
|
||||
|
||||
#Say gGoKeepAlivePeriod(5 seconds) and gGoLinkMonitorPeriod(10 seconds).
|
||||
#For every 10 seconds DUT send Qos Null frame(i.e., Keep Alive frame if link
|
||||
#is idle for last 10 seconds.) For both active and power save clients.
|
||||
|
||||
#Power save clients: DUT set TIM bit from 10th second onwards and till client
|
||||
#honors TIM bit. If doesn't honor for 5 seconds then DUT remove client.
|
||||
|
||||
#Active clients: DUT send Qos Null frame for 10th seconds onwards if it is not
|
||||
#success still we try on 11th second if not tries on 12th and so on till 15th
|
||||
#second. Hence before disconnection DUT will send 5 NULL frames. Hence in any
|
||||
#case DUT will detect client got removed in (10+5) seconds.
|
||||
#i.e., (gGoKeepAlivePeriod + gGoLinkMonitorPeriod)..
|
||||
|
||||
#gGoLinkMonitorPeriod/ gApLinkMonitorPeriod is period where link is idle and
|
||||
#it is period where we send NULL frame.
|
||||
#gApLinkMonitorPeriod = 10
|
||||
#gGoLinkMonitorPeriod = 10
|
||||
|
||||
#gApKeepAlivePeriod is time to spend to check whether frame
|
||||
#are succeed to send or not. Hence total effective detection time is
|
||||
#(gApLinkMonitorPeriod + gApKeepAlivePeriod)
|
||||
|
||||
#STA Keepalive Period
|
||||
gStaKeepAlivePeriod=15
|
||||
|
||||
# Enable DFS channel roam
|
||||
# 0: DISABLE, 1: ENABLED_NORMAL, 2: ENABLED_ACTIVE
|
||||
gAllowDFSChannelRoam=1
|
||||
|
||||
gVhtChannelWidth=2
|
||||
|
||||
# Set txchainmask and rxchainmask
|
||||
# These parameters are used only if gEnable2x2 is 0
|
||||
# Valid values are 1,2
|
||||
# Set gSetTxChainmask1x1=1 or gSetRxChainmask1x1=1 to select chain0.
|
||||
# Set gSetTxChainmask1x1=2 or gSetRxChainmask1x1=2 to select chain1.
|
||||
gSetTxChainmask1x1=1
|
||||
gSetRxChainmask1x1=1
|
||||
|
||||
# MCC to SCC Switch mode:
|
||||
# 0-Disable
|
||||
# 1-Enable
|
||||
# 2-Force SCC if same band, with SAP restart
|
||||
# 3-Force SCC if same band, without SAP restart by sending (E)CSA
|
||||
# 4-Force SCC if same band (or) use SAP mandatory channel for DBS,
|
||||
# without SAP restart by sending (E)CSA
|
||||
gWlanMccToSccSwitchMode = 4
|
||||
|
||||
# 1=enable tx STBC; 0=disable
|
||||
gEnableTXSTBC=1
|
||||
|
||||
#Enable/Disable Tx beamformee in SAP mode
|
||||
gEnableTxBFeeSAP=1
|
||||
|
||||
# Enable Tx beamforming in VHT20MHz
|
||||
# Valid values are 0,1. If commented out, the default value is 0.
|
||||
# 0=disable, 1=enable
|
||||
gEnableTxBFin20MHz=1
|
||||
|
||||
#Enable/Disable SU Tx beamformer support
|
||||
gEnableTxSUBeamformer=1
|
||||
|
||||
# 802.11K support
|
||||
gRrmEnable=1
|
||||
|
||||
# Firmware log mode
|
||||
# Valid values are 0,1,2
|
||||
# 0=Disable, 1=WMI, 2=DIAG
|
||||
gEnablefwlog=1
|
||||
|
||||
# Maximum Receive AMPDU size (VHT only. Valid values:
|
||||
# 0->8k 1->16k 2->32k 3->64k 4->128k)
|
||||
gVhtAmpduLenExponent=7
|
||||
|
||||
# Maximum MPDU length (VHT only. Valid values:
|
||||
# 0->3895 octets, 1->7991 octets, 2->11454 octets)
|
||||
gVhtMpduLen=2
|
||||
|
||||
#Enable or Disable p2p device address administered
|
||||
isP2pDeviceAddrAdministrated=1
|
||||
|
||||
#Enable VHT on 2.4Ghz
|
||||
gEnableVhtFor24GHzBand=1
|
||||
|
||||
#Maximum number of offload peers supported
|
||||
# gMaxOffloadPeers=2
|
||||
|
||||
# controlling the following offload patterns
|
||||
# through ini parameter. Default value is 1
|
||||
# to disable set it to zero. ssdp = 0
|
||||
# Setup multicast pattern for mDNS 224.0.0.251,
|
||||
# SSDP 239.255.255.250 and LLMNR 224.0.0.252
|
||||
ssdp=0
|
||||
|
||||
# RA filtering rate limit param, the current value would not
|
||||
# help if the lifetime in RA is less than 3*60=3min. Then
|
||||
# we need to change it, though it is uncommon.
|
||||
# gRAFilterEnable=0
|
||||
gRArateLimitInterval=600
|
||||
|
||||
# Maximum number of concurrent connections
|
||||
gMaxConcurrentActiveSessions=3
|
||||
|
||||
# Disable/Enable GreenAP
|
||||
# 0 to disable, 1 to enable, default: 1
|
||||
gEnableGreenAp=0
|
||||
|
||||
#Enable/Disable LPASS support
|
||||
# 0 to disable, 1 to enable
|
||||
gEnableLpassSupport=1
|
||||
|
||||
# Whether userspace country code setting shld have priority
|
||||
gCountryCodePriority=1
|
||||
|
||||
# Enable or Disable Multi-user MIMO
|
||||
# 1=Enable (default), 0=Disable
|
||||
gEnableMuBformee=1
|
||||
|
||||
# Enable support for TDLS
|
||||
# 0 - disable
|
||||
# 1 - enable
|
||||
gEnableTDLSSupport=1
|
||||
|
||||
# Enable support for Implicit Trigger of TDLS. That is, wlan driver shall
|
||||
# initiate TDLS Discovery towards a peer whenever setup criteria (throughput
|
||||
# and RSSI) is met and then will initiate teardown when teardown criteria
|
||||
# (idle packet count and RSSI) is met.
|
||||
# 0 - disable
|
||||
# 1 - enable
|
||||
gEnableTDLSImplicitTrigger=1
|
||||
|
||||
# Changed to 0 for Samsung to enable explicit TDLS withough supplicant change
|
||||
# Enable TDLS External Control. That is, user space application has to
|
||||
# first configure a peer MAC in wlan driver towards which TDLS is desired.
|
||||
# Device will establish TDLS only towards those configured peers whenever
|
||||
# TDLS criteria (throughput and RSSI threshold) is met and teardown TDLS
|
||||
# when teardown criteria (idle packet count and RSSI) is met. However,
|
||||
# device will accept TDLS connection if it is initiated from any other peer,
|
||||
# even if that peer is not configured.
|
||||
# 0 - disable
|
||||
# 1 - enable
|
||||
# For TDLS External Control, Implicit Trigger must also be enabled.
|
||||
gTDLSExternalControl=0
|
||||
|
||||
# Changed to 0 for Samsung to disable TDLS offchannel
|
||||
# Enable support for TDLS off-channel operation
|
||||
# 0 - disable
|
||||
# 1 - enable
|
||||
# TDLS off-channel operation will be invoked when there is only one
|
||||
# TDLS connection.
|
||||
gEnableTDLSOffChannel=0
|
||||
|
||||
gSoftApMaxPeers=8
|
||||
gTDLSMaxPeerCount=1
|
||||
|
||||
# Enable Mutiple TDLS links
|
||||
gEnableTDLSBufferSta=0
|
||||
gTDLSUapsdMask=0
|
||||
gTDLSRSSITeardownThreshold=-95
|
||||
|
||||
# TDLS Packet Threshold
|
||||
gTDLSTxPacketThreshold=200
|
||||
|
||||
# VHT Tx/Rx MCS values
|
||||
# Valid values are 0,1,2. If commented out, the default value is 0.
|
||||
# 0=MCS0-7, 1=MCS0-8, 2=MCS0-9
|
||||
gVhtRxMCS=2
|
||||
gVhtTxMCS=2
|
||||
|
||||
# VHT Tx/Rx MCS values for 2x2
|
||||
# Valid values are 0,1,2. If commented out, the default value is 0.
|
||||
# 0=MCS0-7, 1=MCS0-8, 2=MCS0-9
|
||||
gEnable2x2=1
|
||||
gVhtRxMCS2x2=2
|
||||
gVhtTxMCS2x2=2
|
||||
|
||||
#IPA config is a bit mask and following are the configurations.
|
||||
#bit0 IPA Enable
|
||||
#bit1 IPA PRE Filter enable
|
||||
#bit2 IPv6 enable
|
||||
#bit3 IPA Resource Manager (RM) enable
|
||||
#bit4 IPA Clock scaling enable
|
||||
#bit5 IPA uC ENABLE
|
||||
#bit6 IPA uC STA ENABLE
|
||||
#bit8 IPA Real Time Debugging
|
||||
gIPAConfig=0
|
||||
gIPADescSize=800
|
||||
|
||||
# Increase TCL ringsize
|
||||
dp_tx_ring_size=3072
|
||||
|
||||
#Disable HW checksum for Legacy modes
|
||||
legacy_mode_csum_disable=1
|
||||
|
||||
# Enable TCP Segmentation Offload
|
||||
# 1 - enable 0 - disable
|
||||
TSOEnable=1
|
||||
|
||||
# Enable Generic Receive Offload
|
||||
# 1 - enable(default) 0 - disable
|
||||
GROEnable=1
|
||||
|
||||
# Enable HT MPDU Density
|
||||
# 4 for 2 micro sec
|
||||
ght_mpdu_density=4
|
||||
|
||||
# Enable flow steering to enable multiple CEs for Rx flows.
|
||||
# Multiple Rx CEs<==>Multiple Rx IRQs<==>probably different CPUs.
|
||||
# Parallel Rx paths.
|
||||
# 1 - enable 0 - disable(default)
|
||||
gEnableFlowSteering=1
|
||||
|
||||
# Enable Rx FISA support
|
||||
# 0 - disable(default for non-QCA6490), 1 - enable(default for QCA6490)
|
||||
dp_rx_fisa_enable=0
|
||||
|
||||
# Maximum number of MSDUs the firmware will pack in one HTT_T2H_MSG_TYPE_RX_IN_ORD_PADDR_IND
|
||||
maxMSDUsPerRxInd=8
|
||||
|
||||
################ Datapath feature set End ################
|
||||
|
||||
################ NAN feature set start ###################
|
||||
|
||||
# Enable NAN discovery (NAN 1.0)
|
||||
# 1 - enable 0 - disable(default)
|
||||
gEnableNanSupport=1
|
||||
# Enable NAN Datapath
|
||||
genable_nan_datapath=1
|
||||
|
||||
################ NAN feature set end #####################
|
||||
|
||||
hostscan_adaptive_dwell_mode=1
|
||||
|
||||
# Enable/Disable rtt sta mac randomization
|
||||
enable_rtt_mac_randomization=1
|
||||
|
||||
#Enable/Disable SNR monitoring
|
||||
gEnableSNRMonitoring=1
|
||||
|
||||
gEnableConcurrentSTA=wlan1
|
||||
gEnableSAPManadatoryChanList=1
|
||||
|
||||
# HTC Credit count for WMI operation
|
||||
# 1 to serialize the WMI commands
|
||||
# 0 default works with FW advertised credits, 2 credits usually
|
||||
gWmiCreditCount=1
|
||||
|
||||
# Added for Samsung HST
|
||||
# For enabled 11ac SAP
|
||||
gSAP11ACOverride=1
|
||||
# Enable enhanced ACS
|
||||
acs_with_more_param=1
|
||||
# bits 0-3: rssi weight
|
||||
# bits 4-7: bss count weight
|
||||
# bits 8-11: noise floor weight
|
||||
# bits 12-15: channel free weight
|
||||
# bits 16-19: tx power range weight
|
||||
# bits 20-23: tx power throughput weight
|
||||
# bits 24-31: reserved
|
||||
AutoChannelSelectWeight=0x00fafafa
|
||||
|
||||
# Enable/Disable broadcast TWT
|
||||
bcast_twt=1
|
||||
|
||||
#Disable twt
|
||||
twt_congestion_timeout=0
|
||||
|
||||
# Enable Runtime PM
|
||||
# 0 - RTPM disabled, so CxPC aware RTPM will be disabled as well
|
||||
# 1 - RTPM enabled, but CxPC aware RTPM disabled (i.e, Static Runtime PM)
|
||||
# 2 - RTPM enabled and CxPC aware RTPM enabled as well (i.e, Dynamic Runtime PM)
|
||||
gRuntimePM=0
|
||||
gRuntimePMDelay=500
|
||||
|
||||
# QMI stats
|
||||
enable_qmi_stats=0
|
||||
|
||||
# sae connect retry
|
||||
sae_connect_retries=0x52
|
||||
|
||||
# join retry timer on failure
|
||||
join_failure_retry_interval=1000
|
||||
|
||||
gActiveMaxChannelTime=80
|
||||
active_max_channel_time_6g=60
|
||||
passive_max_channel_time_6g=60
|
||||
|
||||
# Enable broadcast logging to the userspace entities
|
||||
gMulticastHostFwMsgs=1
|
||||
# Disable packetlog explicitly
|
||||
gEnablePacketLog=0
|
||||
|
||||
# Set IPA bandwidth levels in mbps
|
||||
gIPALowBandwidthMbps=100
|
||||
gIPAMediumBandwidthMbps=400
|
||||
gIPAHighBandwidthMbps=800
|
||||
|
||||
# Enable wlm_latency_enable feature
|
||||
# 0 - disable, 1 - enable(default)
|
||||
wlm_latency_enable=1
|
||||
wlm_latency_flags_low=0x420000
|
||||
wlm_latency_flags_ultralow=0x420000
|
||||
spectral_disable=1
|
||||
|
||||
# This ini is used to give higher priority for 5g scc than dbs.
|
||||
# It is bitmap per enum policy_mgr_con_mode.
|
||||
# For example in GO+STA(5G) mode, when TPUT is onfigured as wlan system
|
||||
# preference option, If 5G SCC needs higher priority than dbs, set it as 8.
|
||||
g_prefer_5g_scc_to_dbs=8
|
||||
|
||||
# To get PCIe debug info
|
||||
gEnableSelfRecovery=1
|
||||
#Roaming enhancements related ini
|
||||
enable_bss_load_roam_trigger=1
|
||||
bss_load_threshold=70
|
||||
bss_load_sample_time=10000
|
||||
bss_load_trigger_2g_rssi_threshold=-60
|
||||
bss_load_trigger_5g_rssi_threshold=-70
|
||||
enable_idle_roam=1
|
||||
idle_roam_band=1
|
||||
idle_roam_inactive_time=10
|
||||
idle_roam_min_rssi=-60
|
||||
idle_roam_rssi_delta=5
|
||||
idle_data_packet_count=5
|
||||
enable_disconnect_roam_offload=1
|
||||
enable_adaptive_11r=1
|
||||
gNeighborLookupThreshold=75
|
||||
gEmptyScanRefreshPeriod=10000
|
||||
roam_scan_inactivity_time=10000
|
||||
roam_scan_period_after_inactivity=120000
|
||||
roam_inactive_data_count=5
|
||||
roam_score_delta=20
|
||||
roam_score_delta_bitmap=0xFFFFFFFF
|
||||
btm_roam_score_delta=0
|
||||
idle_roam_score_delta=1
|
||||
candidate_min_rssi_for_beacon_miss=-76
|
||||
candidate_min_rssi_for_disconnect=-76
|
||||
btm_disassoc_timer_threshold=10000
|
||||
nr_offload_params_bitmask=1
|
||||
nr_offload_time_offset=1
|
||||
btm_offload_config=449
|
||||
roam_candidate_validity_timer=0
|
||||
minimum_btm_candidate_score=6000
|
||||
roam_bad_rssi_thresh_offset_2g=0
|
||||
roam_bg_scan_client_bitmap=0
|
||||
rssi_weightage=65
|
||||
channel_congestion_weightage=35
|
||||
ht_caps_weightage=0
|
||||
vht_caps_weightage=0
|
||||
he_caps_weightage=0
|
||||
chan_width_weightage=0
|
||||
nss_weightage=0
|
||||
chan_band_weightage=0
|
||||
beamforming_cap_weightage=0
|
||||
pcl_weightage=0
|
||||
oce_wan_weightage=0
|
||||
vendor_roam_score_algorithm=1
|
||||
gNeighborScanChannelMaxTime=40
|
||||
gRoamScanHomeAwayTime=100
|
||||
RoamRssiDiff=10
|
||||
gFullRoamScanPeriod=120
|
||||
gRoamScanNProbes=2
|
||||
gWESModeEnabled=0
|
||||
min_roam_score_delta=1500
|
||||
gper_roam_enabled=0
|
||||
groam_dense_rssi_thresh_offset=0
|
||||
gRoamScanHiRssiDelta=0
|
||||
gChannelBondingMode24GHz=1
|
||||
sae_single_pmk_feature_enabled=1
|
||||
gDroppedPktDisconnectTh=0
|
||||
gEnableNUDTracking=0
|
||||
|
||||
#gEnableIpTcpUdpChecksumOffload=0
|
||||
gHandleLatencyCriticalClients=1
|
||||
|
||||
etsi13_srd_chan_in_master_mode=7
|
||||
|
||||
#acquire wake lock during user scan
|
||||
wake_lock_in_user_scan=1
|
||||
|
||||
enable_tcp_param_update=1
|
||||
|
||||
#Removed by request of SS
|
||||
#enable_bcn_rpt_err_vsie=1
|
||||
|
||||
#Removed by request of SS
|
||||
#enable_roam_reason_vsie=1
|
||||
|
||||
sta_disable_roam=3
|
||||
|
||||
#Enable PNO on R-OS
|
||||
gPNOScanSupport=1
|
||||
|
||||
END
|
||||
|
||||
# Note: Configuration parser would not read anything past the END marker
|
||||
|
||||
Reference in New Issue
Block a user