lime: Generate vendor blobs

Signed-off-by: HeroBuxx <me@herobuxx.me>

proprietary/vendor/etc/camera/camxoverridesettings.txt

@@ -0,0 +1,6 @@
+dumpSensorEEPROMData=FALSE
+enable3ADebugData=FALSE
+enableTuningMetadata=FALSE
+logInfoMask=0x10080
+overrideLogLevels=0x1F
+RaiseRecoverySigabrt=FALSE

proprietary/vendor/etc/camera/hdr_ui9_params.config

@@ -0,0 +1,35 @@
+static ArcHDRCommonAEParam ArcHDRCommonAEParams[] = {
+/*
+lux_min, lux_max, checkermode, c_min, c_max, drc_min, drc_max*/
+//CommonAEParam
+{250,    300,         1,       0.6,   0.8,   4.0,    8.0},
+};
+static ArcHDRParam ArcHDRParams[] = {
+/*
+tonelen, bright, saturation, contrast, capture_num, r_ev0, r_ev-, r_ev+*/
+//REAR camera
+{20,    -15,              5,       50,         3,    0,   -10,    6},
+//FRONT camera
+{1,       0,              0,        0,         2,    0,   -12,    0},
+};
+
+#################################################instructions###########################################################################
+/*
+instructions as followed:
+if lux < lux_min
+    dr_mode = hdr;
+if lux > lux_max
+    dr_mode = llhdr;
+else
+    dr_mode = checker's output
+
+if checkermode == EV_AUTO  //automode
+   ev0 ev- ev+ use data from checker
+if checkermode == EV_MANUL  //manualmode
+   ev0 ev- ev+ use data from config
+
+if confval < c_min
+   dr_mode disabled
+if confval > c_max
+   dr_mode enabled
+*/

proprietary/vendor/etc/camera/vidhance_calibration

@@ -0,0 +1 @@
+>Icccca5$16(2-aycpoIcccca%2& /$-*7+

proprietary/vendor/etc/libnfc-hal-st.conf

@@ -0,0 +1,156 @@
+########################### Start of libnfc-hal-st.conf ###########################
+
+###############################################################################
+###############################################################################
+# ST HAL trace log level
+#define STNFC_TRACE_LEVEL_NONE    0x00
+#define STNFC_TRACE_LEVEL_ERROR   0x01
+#define STNFC_TRACE_LEVEL_WARNING 0x02
+#define STNFC_TRACE_LEVEL_DEBUG   0x03
+#define STNFC_TRACE_LEVEL_VERBOSE 0x04
+#define STNFC_TRACE_FLAG_PRIVACY  0x10
+STNFC_HAL_LOGLEVEL=0x03
+
+NFC_DEBUG_ENABLED=1
+
+###############################################################################
+# Vendor specific mode to enable FW (RF & SWP) traces.
+STNFC_FW_DEBUG_ENABLED=1
+
+###############################################################################
+# File used for NFA storage
+NFA_STORAGE="/data/nfc"
+
+###############################################################################
+# Keep the nfa storage file.
+PRESERVE_STORAGE=1
+
+###############################################################################
+# In Switch OFF mode (phone switched-off), specify the desired CE mode to
+# the controller.
+# 0: No card-emulation; DEFAULT
+# 1: Switch-off card-emulation enabled
+CE_ON_SWITCH_OFF_STATE=1
+
+###############################################################################
+# Vendor specific mode to support the USB charging mode if VPSIO=1 in switch off.
+STNFC_USB_CHARGING_MODE=1
+
+###############################################################################
+# Vendor Specific Proprietary Protocol & Discovery Configuration
+# Set to 0xFF if unsupported
+#  byte[0] NCI_PROTOCOL_18092_ACTIVE
+#  byte[1] NCI_PROTOCOL_B_PRIME
+#  byte[2] NCI_PROTOCOL_DUAL
+#  byte[3] NCI_PROTOCOL_15693
+#  byte[4] NCI_PROTOCOL_KOVIO
+#  byte[5] NCI_PROTOCOL_MIFARE
+#  byte[6] NCI_DISCOVERY_TYPE_POLL_KOVIO
+#  byte[7] NCI_DISCOVERY_TYPE_POLL_B_PRIME
+#  byte[8] NCI_DISCOVERY_TYPE_LISTEN_B_PRIME
+NFA_PROPRIETARY_CFG={05:FF:FF:06:8A:90:77:FF:FF}
+
+###############################################################################
+# Choose the presence-check algorithm for type-4 tag.  If not defined,
+# the default value is 1.
+# 0  NFA_RW_PRES_CHK_DEFAULT; Let stack selects an algorithm
+# 1  NFA_RW_PRES_CHK_I_BLOCK; ISO-DEP protocol's empty I-block
+# 2  NFA_RW_PRES_CHK_RESET; Deactivate to Sleep, then re-activate
+# 3  NFA_RW_PRES_CHK_RB_CH0; Type-4 tag protocol's ReadBinary command on channel 0
+# 4  NFA_RW_PRES_CHK_RB_CH3; Type-4 tag protocol's ReadBinary command on channel 3
+# 5  NFA_RW_PRES_CHK_ISO_DEP_NAK; presence check command ISO-DEP NAK as per NCI2.0
+PRESENCE_CHECK_ALGORITHM=5
+
+###############################################################################
+# Name of the NCI HAL module to use
+# If unset, falls back to nfc_nci.bcm2079x
+NCI_HAL_MODULE="nfc_nci.st21nfc"
+
+###############################################################################
+# White list to be set at startup.
+DEVICE_HOST_WHITE_LIST={02:C0}
+
+###############################################################################
+# BAIL OUT value for P2P
+# Implements algorithm for NFC-DEP protocol priority over ISO-DEP protocol.
+POLL_BAIL_OUT_MODE=1
+
+###############################################################################
+# Extended APDU length for ISO_DEP
+ISO_DEP_MAX_TRANSCEIVE=0xFEFF
+
+###############################################################################
+# Configure the NFC Extras to open and use a static pipe.  If the value is
+# not set or set to 0, then the default is use a dynamic pipe based on a
+# destination gate (see NFA_HCI_DEFAULT_DEST_GATE).  Note there is a value
+# for each EE (ESE/SIM)
+OFF_HOST_ESE_PIPE_ID=0x5E
+OFF_HOST_SIM_PIPE_ID=0x3E
+
+###############################################################################
+#Set the default Felica T3T System Code OffHost route Location :
+#This settings will be used when application does not set this parameter
+# host  0x00
+# eSE   0x82 (eSE),    0x86 (eUICC/SPI-SE)
+# UICC  0x81 (UICC_1), 0x85 (UICC_2)
+DEFAULT_SYS_CODE_ROUTE=0x81
+
+###############################################################################
+#Set the Felica T3T System Code supported power state:
+DEFAULT_SYS_CODE_PWR_STATE=0x3B
+
+###############################################################################
+# Path and Files used for FW update binaries storage
+STNFC_FW_PATH_STORAGE="/vendor/firmware/"
+STNFC_FW_BIN_NAME="st21nfc_fw.bin"
+STNFC_FW_CONF_NAME="/vendor/etc/st21nfc_conf.txt"
+
+###############################################################################
+# Default off-host route for Felica.
+#This settings will be used when application does not set this parameter
+# host  0x00
+# eSE   0x82 (eSE),    0x86 (eUICC/SPI-SE)
+# UICC  0x81 (UICC_1), 0x85 (UICC_2)
+DEFAULT_NFCF_ROUTE=0x81
+
+###############################################################################
+# Configure the default off-host route.
+# used for technology A and B routing
+# eSE   0x82 (eSE),    0x86 (eUICC/SPI-SE)
+# UICC  0x81 (UICC_1), 0x85 (UICC_2)
+DEFAULT_OFFHOST_ROUTE=0x81
+
+###############################################################################
+# Configure the default AID route.
+# host  0x00
+# eSE   0x82 (eSE),    0x86 (eUICC/SPI-SE)
+# UICC  0x81 (UICC_1), 0x85 (UICC_2)
+DEFAULT_ROUTE=0x81
+
+###############################################################################
+# Configure the NFCEEIDs of offhost UICC.
+# UICC  0x81 (UICC_1), 0x85 (UICC_2)
+OFFHOST_ROUTE_UICC={81,83,85}
+
+###############################################################################
+# Configure the NFCEEIDs of offhost eSEs.
+# eSE   0x82 (eSE),    0x86 (eUICC/SPI-SE)
+OFFHOST_ROUTE_ESE={82,86}
+
+###############################################################################
+# Configure the list of NFCEE for the ISO-DEP routing.
+# host  0x00
+# eSE   0x82 (eSE),    0x86 (eUICC/SPI-SE)
+# UICC  0x81 (UICC_1), 0x85 (UICC_2)
+DEFAULT_ISODEP_ROUTE=0x81
+
+###############################################################################
+# Core configuration settings
+CORE_CONF_PROP={ 20, 02, 13, 06,
+        a1, 01, 19,
+        a2, 01, 15,
+        80, 01, 01,
+        08, 01, 01,
+        11, 01, 01,
+        19, 01, 01
+}

proprietary/vendor/etc/libnfc-nci.conf

@@ -0,0 +1,148 @@
+########################### Start of libnfc-nci.conf ###########################
+
+###############################################################################
+# Application options
+NFC_DEBUG_ENABLED=0
+
+###############################################################################
+# File used for NFA storage
+NFA_STORAGE="/data/nfc"
+
+###############################################################################
+# Force UICC to only listen to the following technology(s).
+# The bits are defined as tNFA_TECHNOLOGY_MASK in nfa_api.h.
+# Default is NFA_TECHNOLOGY_MASK_A | NFA_TECHNOLOGY_MASK_B | NFA_TECHNOLOGY_MASK_F
+UICC_LISTEN_TECH_MASK=0x07
+
+###############################################################################
+# AID for Empty Select command
+# If specified, this AID will be substituted when an Empty SELECT command is
+# detected.  The first byte is the length of the AID.  Maximum length is 16.
+AID_FOR_EMPTY_SELECT={08:A0:00:00:01:51:00:00:00}
+
+###############################################################################
+# Force tag polling for the following technology(s).
+# The bits are defined as tNFA_TECHNOLOGY_MASK in nfa_api.h.
+# Default is NFA_TECHNOLOGY_MASK_A | NFA_TECHNOLOGY_MASK_B |
+#            NFA_TECHNOLOGY_MASK_F | NFA_TECHNOLOGY_MASK_ISO15693 |
+#            NFA_TECHNOLOGY_MASK_B_PRIME | NFA_TECHNOLOGY_MASK_KOVIO |
+#            NFA_TECHNOLOGY_MASK_ACTIVE
+#
+# Notable bits:
+# NFA_TECHNOLOGY_MASK_A	        0x01    /* NFC Technology A             */
+# NFA_TECHNOLOGY_MASK_B	        0x02    /* NFC Technology B             */
+# NFA_TECHNOLOGY_MASK_F	        0x04    /* NFC Technology F             */
+# NFA_TECHNOLOGY_MASK_V       	0x08    /* NFC Technology V             */
+# NFA_TECHNOLOGY_MASK_KOVIO	    0x20    /* Proprietary Technology       */
+# NFA_TECHNOLOGY_MASK_ACTIVE    0x40    /* NFC Technology ACM active mode */
+POLLING_TECH_MASK=0x4F
+
+###############################################################################
+# Force P2P to only listen for the following technology(s).
+# The bits are defined as tNFA_TECHNOLOGY_MASK in nfa_api.h.
+# Default is NFA_TECHNOLOGY_MASK_ACTIVE
+# (type A passive is ignored to avoid interop issues in China).
+# (type F passive is ignored to support Japan)
+#
+# Notable bits:
+# NFA_TECHNOLOGY_MASK_A             0x01    /* NFC Technology A             */
+# NFA_TECHNOLOGY_MASK_F             0x04    /* NFC Technology F             */
+# NFA_TECHNOLOGY_MASK_ACTIVE         0x40    /* NFC Technology Active        */
+P2P_LISTEN_TECH_MASK=0x40
+
+###############################################################################
+# Keep the nfa storage file.
+PRESERVE_STORAGE=0x01
+
+###############################################################################
+# Override the stack default for NFA_EE_MAX_EE_SUPPORTED set in nfc_target.h.
+# The value is set to 3 by default as it assumes we will discover 0xF2,
+# 0xF3, and 0xF4. If a platform will exclude and SE, this value can be reduced
+# so that the stack will not wait any longer than necessary.
+# Maximum EE supported number
+NFA_MAX_EE_SUPPORTED=0x03
+
+
+###############################################################################
+# When screen is turned OFF, specify the desired CE mode to the controller.
+# 0: No card-emulation; DEFAULT
+# 1: Screen-off card-emulation enabled
+CE_ON_SCREEN_OFF_STATE=1
+
+###############################################################################
+# In Switch OFF mode (phone switched-off), specify the desired CE mode to
+# the controller.
+# 0: No card-emulation; DEFAULT
+# 1: Switch-off card-emulation enabled
+CE_ON_SWITCH_OFF_STATE=1
+
+
+###############################################################################
+# When screen is turned off, specify the desired power state of the controller.
+# 0: power-off-sleep state; DEFAULT
+# 1: full-power state
+# 2: screen-off card-emulation (CE4/CE3/CE1 modes are used)
+SCREEN_OFF_POWER_STATE=1
+
+###############################################################################
+# AID_MATCHING constants
+# AID_MATCHING_EXACT_ONLY 0x00
+# AID_MATCHING_EXACT_OR_PREFIX 0x01
+# AID_MATCHING_PREFIX_ONLY 0x02
+# AID_MATCHING_EXACT_OR_SUBSET_OR_PREFIX 0x03
+AID_MATCHING_MODE=0x03
+
+
+###############################################################################
+#Set the default Felica T3T System Code :
+#This settings will be used when application does not set this parameter
+DEFAULT_SYS_CODE={FE:FE}
+
+
+###############################################################################
+# Value of NCI parameter NFCC_CONFIG_CONTROL
+# 0x00  NFCC is not allowed to manage RF configuration
+# 0x01  NFCC is allowed to manage RF configuration
+NFCC_CONFIG_CONTROL=0x01
+
+###############################################################################
+#Select NCI device power states in which routing to off-host element is allowed.
+#Default: 0x3B.
+OFFHOST_AID_ROUTE_PWR_STATE=0x3B
+
+###############################################################################
+# Use generic mifare reader implementation, not proprietary one.
+LEGACY_MIFARE_READER=0x0
+
+###############################################################################
+# Block routing for unsupported power states
+# It means for AID routed to HCE, an error is returned in power modes not supported
+# by HCE (screen off, switch off) instead of routing to the secure element.
+# This behavior is required for GSMA certification.
+NFA_AID_BLOCK_ROUTE=1
+
+
+###############################################################################
+#Set the HCE supported techs:
+#define NFA_TECHNOLOGY_MASK_A 0x01 /* NFC Technology A             */
+#define NFA_TECHNOLOGY_MASK_B 0x02 /* NFC Technology B             */
+#define NFA_TECHNOLOGY_MASK_F 0x04 /* NFC Technology F             */
+HOST_LISTEN_TECH_MASK = 0x7
+
+###############################################################################
+# EXPERIMENTAL
+# Stack attempts to automatically detect when a reader fails to establish a link
+# with this device and the firmware mechanisms for dynamic settings are not
+# effective. Stack then attempts to switch the RF parameters to try different
+# settings. Mechanism based on timers and patterns.
+# - only with firmware >= 1.7
+# - requires the firmware logs to be enabled
+#     (STNFC_FW_DEBUG_ENABLED=1 in libnfc-hal-st.conf -- you may need to change
+#      the file libnfc-hal-st.conf.user in your source tree)
+# - only for type A transactions at the moment.
+# Default : mechanism is disabled.
+#RF_PARAMS_AUTO_SWITCH=0
+#RF_PARAMS_AUTO_SWITCH_ERR_THRESHOLD=3
+#RF_PARAMS_AUTO_SWITCH_T1_THRESHOLD=50
+#RF_PARAMS_AUTO_SWITCH_T2_THRESHOLD=500
+#RF_PARAMS_AUTO_SWITCH_CYCLES=2

proprietary/vendor/etc/st21nfc_conf.txt

@@ -0,0 +1,44 @@
+REM CONFIG CRC IS 0BA9
+HW_RESET_I2C,00,
+SLEEP,00,2000,
+NCI_CORE_RESET,00,
+NCI_CORE_INIT,0000,
+SLEEP,00,200
+REM RESET THE CUSTOMER FIELD
+NCI_SEND_PROP,0F,02,040006010008000000000000a5a5
+SLEEP,00,200
+REM HARDWARE CONFIGURATION
+NCI_SEND_PROP,0F,02,040002010024201206138801F404000A07FF080203058900000800000000000000000A07531410000009
+SLEEP,00,200
+REM Writing CustomA RF Parameters
+NCI_SEND_PROP,0F,02,0400100100DCC05936ACA90C00D50000FFAF0000FFAF075F600701010103000000000000000000000000EA005928000F000000000000880000008800000088000000880000008800000070707040400101010101FEFEFEFEFE1D1D1D1D1DF3F3F3F3F3E2E2E2E2E200000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000010101000002020201010303030202040404030305050504040606060505070707060607070707070707070707070707070702C2C2C2D2DFFFFFFFFFF0000
+REM Writing CustomB RF Parameters
+NCI_SEND_PROP,0F,02,040010010154C05941AC08040242040402421303142D3D3D3D3D3D3D3D2C2C2C000000000000000000FC000000000000000000000000404040E04040404040404091949444959595450000000000000000000000000000000000
+REM Set DPC table
+NCI_DIRECT_CTRL,2F,02,04000301004A6F0CBB0CFF0C540D9F0DEB0D360E7F0ECD0E170F5F0F9F0FC70FEE0FFF0FFF0FFF08FF08FF08FF08FF08FF085B09B209050A530A9F0AEF0A3B0B8A0BD30B0D0CFF0FFF0FFF0FFFFFFF1F
+SLEEP,00,200
+REM UICC CONFIG
+NCI_DIRECT_CTRL,2F,02,04000A01001A48003C3C04B027100AF007D003E807D00064271003E832C81964
+SLEEP,00,200
+REM SE CONFIG
+NCI_DIRECT_CTRL,2F,02,04000B01001A40041E1E04B027100AF007D003E807D00064271003E832C81964
+SLEEP,00,200
+REM IOT CONFIG
+NCI_DIRECT_CTRL,2F,02,04000801000CDF0169000000C1C2C3003D00
+SLEEP,00,200
+REM ANTENNA CONFIG
+NCI_DIRECT_CTRL,2F,02,0400090100200000E10BB801B5FFEC0000000000000000000000000000000000000000000000
+SLEEP,00,200
+REM NFCC CONFIG
+NCI_DIRECT_CTRL,2F,02,0400010100050053000606
+SLEEP,00,200
+REM WRITE CONFIGURATION CRC IN THE CUSTOMER FIELD
+NCI_SEND_PROP,0F,02,0400060100080000000000000BA9
+SLEEP,00,200
+HW_RESET_I2C,00,
+SLEEP,00,2000,
+NCI_CORE_RESET,00,
+NCI_CORE_INIT,0000,
+REM MATCHING ;45.4;3.97;56.6;Differential;Yes;15;560;No;No;ANT;1500;4.7;78;100;1500;77;DNP;150
+REM CONFIGURATION ;810.912065491184;608.032940704434;20.2116351224186;No;No;Differential;Yes;77;680;276;47;DNP;DNP;ANT;150;27;4.7;100;4.5
+REM TOOL VERSION 3.02